Привет всем, у меня 2 вопроса
1. Никак не могу настроить Streamline, плагинов много, вылетов тоже
вот както так примерно, или может что по другому надо? (сорри я чтото не нашла как спойлер сделать)
[hide]
;======================================================================
=========
====
; [Main Features Settings] Toggle Streamline Features (1=on, 0=off)
;===============================================================================
====
set SLv.Purging to 1 ; Turn on Streampurge? (cache purging)
set SLv.FPSsmoothing to 1 ; Turn on Streamsmooth? (FPS smoothing)
>>> If using the Oblivion Stutter Remover, set the FPS range within OSR's (default capped at 30).
>>> Otherwise, disable this option. OSR practically replaces it.
set SLv.Streamsaving to 1 ; Turn on Streamsaving? (timed autosaves)
set SLv.Streamsight to 1 ; Turn on Streamsight? (FPS enhancer)
;===================================================================================
; [Streamsmooth Visual Categories] What can Streamsmooth change on-the-fly?
;===================================================================================
set SLv.setLightShadow to 0 ; Shadow number & range, etc.
>>> If using StreamSmooth seeing flickering of light\shadow in background,
>>> setting this to 0 may alleviate the flickering.
;===============================================================================
====
; [Streampurge Settings] An automated cache-cleaner for Oblivion
;===============================================================================
====
set SLh.SLmode to 4 ; Memory Purge Mode (1-6) (Default: 3)
>>> 4 is recommended by many users
; Lower # = faster, higher # = slower
set SLv.PurgeOnTravel to 0 ; Purge memory on travel & zone?
>>> If enabled, may conflict with running scripts
set SLv.PurgeOnWait to 1 ; Purge memory when character waits?
set SLv.PurgeOnSleep to 1 ; Purge memory when character sleeps?
;===============================================================================
====
; [Streamsave Settings] <--- These are recommended for increased stability and reduced conflicts
;===============================================================================
====
set SLv.SaveTimer to 5 ; Autosave interval (in actual minutes)
>>> Safer for auto-saves
>>> Choose any useful interval
set SLv.NumSaveSlots to 50 ; Number of save slots to use (Max: 60)
>>> Choose the number of slots you find useful
...
>>> The following StreamSave settings, if enabled, may cause trouble for running scripts.
set SLv.AfterCombat to 0 ; Force a save after each combat ends?
set SLv.InteriorOnly to 0 ; Save only when indoors?
set SLv.WhenIdleOnly to 0 ; Save only when character is idle?
set SLv.AfterZone to 0 ; Save after fast-travel or door use?
set SLv.AfterWaitSleep to 0 ; Save after waiting or sleeping?
...
set SLv.PurgeBeforeSave to 0 ; Do a purge before a Streamsave?
;===============================================================================
====
; [Streamsight Settings] <--- Scripted weather mod users - DO NOT FORGET THIS!!
;===============================================================================
====
set SLv.WeatherUnsticker to 0 ; Leave set at 1 unless you use a
; scripted weather mod
>>> Scripted weather mod users (i.e., users of EW, AWS, All Natural, etc) - Do not forget this!!
и вот
set SLv.FPSsmoothing to 0 ; Turn on Streamsmooth? (FPS smoothing)
set SLv.Streamsight to 1 ; Turn on Streamsight? (FPS enhancer)
set SLfpsmon.High to 31 ; Highest minimum FPS (top of range)
set SLfpsmon.Low to 26 ; Lowest minimum FPS (bottom of range)
[/hide]
2.Если много НПС не могу попасть не то что в таверну, даже в город. ОСобенно это ощущается в Бруме.
Стоит From2ch Lives, который в игру добавляет почти 400 НПС, отключать неохота, сразу в городах както пусто становится, хоть ау кричи.
Это можно както преодолеть (вылеты)?
// - применение тегов
